Re: Panacea site

Well it involves a pluse system like Muller but that's a bad example for
this it's removing the core material after the push pulse so the material
doesn't interfere with the other neo's the disk would just free wheel with
a heavy flywheel and no other iron around to lock up the rotation just a
power pulse and pull the cores .greater pulse energy with out any drag
.there getting I think 3.3 OU now with out iron cores just air .Bedini was
talking about it on a vid about Watson's motor once at speed the energizers
would only turn on occasionally because of the stored kinetic in the big
flywheel .that put I in to OU .the thing would just act as a magneto
generator free wheeling .there not much said about stored flywheel energy
and bedini's wheels a little not much .to capture the pulse energy as
motion and use it to turn the wheel is a part of the system .

On Saturday, November 3, 2018, Mick [email protected] [EVGRAY] <
[email protected]> wrote:

>
>
> James very subjective question It depends on the setup and use motor or
> generator, the frequency number of pulses per second how close the coils
> are to one another.  However for small slower motor systems more power/
> torque should be developed with the core than copper alone.  Without the
> core or with very fine core there is less loss due to  Lenz on the
> generating side or when loaded at certain speeds as a motor.  If I got any
> of this wrong Kone can correct me as he is far more knowledgeable with this
> kind of thing.
>
> On 11/3/2018 1:10 PM, James Glinski [email protected] [EVGRAY] wrote:
>
>
>
> I'm going to ask a general question .when using a coil with a magnet for
> turning a wheel .when you use the coil with out a iron core you use x
> amount of power in a pluse .and is it more when you use a iron core in the
> same coil . is the presence of iron just generate a larger magnetic field
> .with out more energy being used. ? Or does the iron core pull more energy
> ? In useage ? Any opinions ?.
>
> On Saturday, November 3, 2018, [email protected] [EVGRAY] <
> [email protected]> wrote:
>
>>
>>
>> Hi Mick
>> Not sure if this related to rotary condenser description, but run cap
>> phase of rotovertor motor is known ad rotary transformer phase (not so much
>> condensor)
>> Kone
>>
>
> 
>

https://en.wikipedia.org/wiki/Synchronous_condenser


On 11/3/2018 2:18 PM, Mick [email protected] [EVGRAY] wrote:
>
> Dave,
>
> By setting up a rotary condenser one can make the analog meters run 
> backwards.   Not sure how the new smart meters process a leading phase 
> angle but doubt they can be manipulated this way.
>
>
> On 11/3/2018 8:13 AM, Dave Muckerman [email protected] [EVGRAY] wrote:
>> Yes, I found that Rotov. adds or subtracts magnetic and physical 
>> momentum if you have just the right motor.
>> I made 10HP Emerson "boat anchor" that didn't work when I found each 
>> pole and counter pole winding was 2 wires together in 
>> parallel(bi-filler, not tesla), and this 240/480V, 4 pole (3.6KRPM) 
>> motor used bifiller windings.
>> So it actually has 48 wires bonded together.
>> I needed to tear all 24 bi-filer ends aprt. to connect them end to 
>> end or series to increase the impedance so now it can start and run 
>> on less power by magnitudes.
>>
>> Another thing one can do by poking through the wire enamel with sharp 
>> ohm-meter probe to find half the DC res. of each pole and 
>> counter-pole, the middle of each wind, and experimenting with this 
>> center-tap.
>>
>> Now think of how a utillity/hydro KWH meter magnetic motor can run 
>> backwards when the magnetic field lag between two or more poles are 
>> reversed.
>>
>>
>> On Saturday, November 3, 2018 6:42 AM, "[email protected] 
>> [EVGRAY]" <[email protected]> wrote:
>>
>>
>> Maybe its more "if you are a bitch at it" its impossible to tune !!! 
>> LOL !
>>
>>
>>
>>
>>
>>
>> ---In [email protected], <laser.rod@...> wrote :
>>
>> H,
>> Like you always say"it's a bitch to tune" right?
>>
>>
>> On Friday, November 2, 2018 8:40 PM, "arkresearch@... [EVGRAY]" 
>> <[email protected]> wrote:
>>
>>
>> He gave up on doing the correct thing ....as there is only one way to 
>> do this mission ...
>>
>>
>>
>>
>> ---In [email protected], <laser.rod@...> wrote :
>>
>> Old news.
>> Ash's site I think.
>> He gave up on the rotoverter and does not post here anymore..
>>
>>
>>
>>
>
>

Thanks Norm, that's what I meant, proper nomenclature is important!


On 11/5/2018 3:43 AM, Norman Wootan [email protected] [EVGRAY] wrote:
>  
>
> https://en.wikipedia.org/wiki/Synchronous_condenser
>
>
> On 11/3/2018 2:18 PM, Mick [email protected] [EVGRAY] wrote:
>>  
>>
>> Dave,
>>
>> By setting up a rotary condenser one can make the analog meters run
>> backwards.   Not sure how the new smart meters process a leading
>> phase angle but doubt they can be manipulated this way.
>>
>>
>> On 11/3/2018 8:13 AM, Dave Muckerman [email protected] [EVGRAY] wrote:
>>>  
>>> Yes, I found that Rotov. adds or subtracts magnetic and physical
>>> momentum if you have just the right motor.
>>> I made 10HP Emerson "boat anchor" that didn't work when I found each
>>> pole and counter pole winding was 2 wires together in
>>> parallel(bi-filler, not tesla), and this 240/480V, 4 pole (3.6KRPM)
>>> motor used bifiller windings.
>>> So it actually has 48 wires bonded together.
>>> I needed to tear all 24 bi-filer ends aprt. to connect them end to
>>> end or series to increase the impedance so now it can start and run
>>> on less power by magnitudes.
>>>
>>> Another thing one can do by poking through the wire enamel with
>>> sharp ohm-meter probe to find half the DC res. of each pole and
>>> counter-pole, the middle of each wind, and experimenting with this
>>> center-tap.
>>>
>>> Now think of how a utillity/hydro KWH meter magnetic motor can run
>>> backwards when the magnetic field lag between two or more poles are
>>> reversed.
>>>
>>>
>>> On Saturday, November 3, 2018 6:42 AM, "[email protected]
>>> [EVGRAY]" <[email protected]> wrote:
>>>
>>>
>>>  
>>> Maybe its more "if you are a bitch at it" its impossible to tune !!!
>>> LOL ! 
>>>
>>>
>>>
>>>
>>>
>>>
>>> ---In [email protected], <laser.rod@...> wrote :
>>>
>>> H,
>>> Like you always say"it's a bitch to tune" right?
>>>
>>>
>>> On Friday, November 2, 2018 8:40 PM, "arkresearch@... [EVGRAY]"
>>> <[email protected]> wrote:
>>>
>>>
>>>  
>>> He gave up on doing the correct thing ....as there is only one way
>>> to do this mission ...
>>>
>>>
>>>
>>>
>>> ---In [email protected], <laser.rod@...> wrote :
>>>
>>> Old news.
>>> Ash's site I think.
>>> He gave up on the rotoverter and does not post here anymore..
>>>
>>>
>>>
>>>
>>
>
>