Body
Warren you said people are having success .could you relate the level of
success with out giving names ?.and hector would know but I think a general
three phase motor like one used in a TV would work too . good hunting .
On Thursday, May 9, 2019, Warren Keillor [email protected]
[EVGRAY] <[email protected]> wrote:
>
>
> Eduardo
> Sadly, the plate if any, was on the gas engine. I only know it was a
> Fairbanks Morse which was very heavily built, using their own engine, which
> for any company, is unusual.
> It seemed to be for continuous duty, but there is no indication when it
> was made, or what model.
> It could have even been war time WW11 vintage except for the paint.
> Cheers Warren
> Sent from Yahoo Mail on Android
> <https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers&af_wl=ym&af_sub1=Internal&af_sub2=Global_YGrowth&af_sub3=EmailSignature>
>
> On Thu., 9 May 2019 at 4:14 a.m., Eduardo Codina
> [email protected] [EVGRAY]
> <[email protected]> wrote:
>
>
> Hi warren, does your generator have a spec. plate, knowing the details,
> model etc could make it easier to get the wiring diagram.
> cheers.
> Eduardo
>
> ----- Forwarded message -----
> *From:* Mick [email protected] [EVGRAY] <[email protected]>
> *To:* "[email protected]" <[email protected]>
> *Sent:* Thursday, 9 May 2019, 11:24:18 am AEST
> *Subject:* Re: [EVGRAY] 120 volt generator
>
>
>
> Warren,
>
> A generator for DC, rather than an alternator producing AC and rectified
> to DC, just spits out DC. The DC slip ring is usually segmented to flip
> the fields.
> On 5/8/2019 2:23 PM, Warren Keillor [email protected]
> [EVGRAY] wrote:
>
>
> Hi Everyone
> I have this 120 volt 60hz single phase generator, four pole 1800 rpm , a
> Fairbanks Morse, possibly from the 1950's. It is very massively built, and
> in decent condition.
> I need such a thing for an experiment I am doing.
> However, it is a challenge to know how to hook it up. I can't find a
> wiring diagram on line.
> It is peculiar. It may predate diodes
> How did they energize the field windings?
> It has a complete commutator, and brushes, as well as slip rings, and
> brushes,
> It was direct coupled to a gas engine. I have installed a stub shaft, and
> a bearing to support the engine end, as the that bearing support was the
> engine bearing.
> It seems pretty good for my purposes if I only can figure out how to make
> it go.
> An interesting feature about it is that it has an electric starter
> function to turn the generator into a motor for starting the gas engine it
> used to be connected to.
> Bart, do you remember that 4 cylinder gas generator I gave you?
> This is likely about a similar vintage, only, this is just a couple of KW,
> I'm hoping will do the job.
> If anybody can remember pre-diode times I would sure be grateful.
> How would the voltage regulation work?
> Cheers Warren
> Sent from Yahoo Mail on Android
> <https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers&af_wl=ym&af_sub1=Internal&af_sub2=Global_YGrowth&af_sub3=EmailSignature>
>
>
>
>