Body
Bart, use the 77 colloidal elements in your cell, a lot of atomic
templates!� See: Elemental Replication.
16 October 1996
*To: Hal Fox,Fusion Facts*
*Elemental Replication ?*
**
Around mid September I put together an electrolysis cell similar to the
Miles Nickel Cold Fusion Cell with the goal of exploring the
possibilities of making what is termed �Pristine Water�.This water which
will be used by Homeopaths will have had all memory or information
removed.This is accomplished by recombining monatomic hydrogen and
monatomic oxygen as generated in a properly designed cell.This is the
ultimate in purity since this is water with conditions at the time of
original creation.�Wholy Water�is a term coined by my dear freind and
fellow researcher Joe Tyls of Vancouver, BC.After several weeks of
successful operation producing water that had all the earmarks of a true
�pristine water� a fellow researcher suggested using an alternate
electrolyte.A solution was selected that contained 77 colloidal minerals
as found in plants that are the easiest assimilated into the body.With
the electrolyte changed the cell was put back into operation as before
with a nice recombination burn and production of the sought after
�pristine water�.
After about an hour of operation the cell went absolutely �nuts� with
the temperature rapidly climbing to boiling point and the current out of
sight.When the cell was opened we found a deep red sludge deposit which
shorted the cell plates.Our first thought was that the electrolytic
action precipitated out the colloidal minerals which caused the deposit
found.Theelectrolyte was allowed to settle out the
precipitate.Afterdecanting off,the clear electrolyte was returned to the
cell for another run. Again the cell operated normally for about an hour
with a normal recombination burn and recovery of the water being
consumed by the cell in the splitting action.Again the cell temperature
and current mirrored the first run.Again the cell contained the same
amount of sludge residue.This process was repeated ten (10) times with
exactly the same results.All of the sludge was carefully dried and
weighed on an electronic scale with a five decimal resolution.The cell
plates and all hardware were weighed to determine any loss of mass that
may contribute to the mass gain observed in the sludge.Five hundred
(500) ml of the original electrolyte solution used in the cell was
vacuum distilled to determine the exact mass of colloidal minerals
contained.When all factors were considered we came out with a mass gain
of48 gm which cannot be explained by conventional electrolysis.
After talking to Dr. Robert Bass and Hal Fox I learned of a patent that
has been filed on the transmutation of elements in the cold fusion cell
which is the process that Dr. John Bockris has been so active in.Both
Dr. Bass and Hal Fox stated that what I was observing is not the same as
the transmutation observed in the cold fusion cell since I have a
overall mass gain and not a lateral movement of elements in the periodic
table toward lighter elements with a resulting heat release.This unusual
cell operation has caused quite a reaction in the scientific community.
At this time I have built a complete new cell with every possible factor
which could possibly explain the mass gain considered and documented.The
ten (10) consecutive runs on the new cell will be completed soon and a
report will be forthcoming.What is interesting about this phenomenon is
that when an eleventh run was made with the original electrolyte exactly
the same amount of residue was recovered as in the previous ten runs.
Since the same electrolyte is reused each time with only distilled water
being added to replace the volume lost by the removal of the solids and
the water recovered by the recombination burn we are hard pressed to
explain the observed phenomenon.The electrolyte appears stronger in
mineral concentration and shows no sign of depletion.
After confering with Joe Tyls we arrived at the conclusion that the 77
colloidal minerals contained in the electrolyte provide the atomic
templates needed for the monatomic hydrogen (father of all the elements)
to replicate selected elements in this exotic mixture.If you subscribe
to the theories of the late Walter Russell and his explanation of the
octave based periodic table with monatonic hydrogen being what he
describes as hydrons (precursor to hydrogen) then it is possible for the
replication of elements directly from energy input alone.This is how all
matter was created in the beginning as described by Schappeller in �The
Physics of the Primary State of Matter�.I will keep all informed as to
our progress and findings in this very intriguing venture.
Norman Wootan
P.O. Box 141049
Dallas, TX 75214
(214) 360-0865
CC:Gene Mallove, Infinite Energy
CC:Dr. John Bockris, Texas A/M
On 1/22/2019 3:16 PM, bart woodard [email protected] [EVGRAY] wrote:
>
> Mick,
> ���������������� Cool....
> https://en.wikipedia.org/wiki/Thyratron
> <https://en.wikipedia.org/wiki/Thyratron>
>
> I remember from a retired electronic engineer� speaking on something
> like this, what gases are you using?
> He said I think there was a standard one available in the 50s and 60s.
> Triode� maybe ( a stable gain with in, cathode applications ?) , I do
> not recall the details.
> Said they stopped making them but there was a knock off available from
> Russia.� Whats your application?
>
> The construction on my favorite cell is really nothing special ,
> currently just hammering elements for now looking for reaction times,
> in hopes of getting the best values with in a specific time of efforts.
> A Fleischmann and Pons � exercise� only a wider variant of elements
> with increased inputs.
> Symbiotic like values. such as .1�� .01 .001 ,0001 and so on.
> �The higher the temp , the higher the exchange rates, the longer� and
> higher stay of a quick pressures kind of thing.
> Hoping to get a combined attachment that can be a standard.
> Currently I am out of time on my daily schedule again .
> I would how ever like to get some thing to solve the controller aspect.
> ------------------------------------------------------------------------
> *From:* [email protected] <[email protected]> on behalf of
> Mick [email protected] [EVGRAY] <[email protected]>
> *Sent:* January 22, 2019 9:33 AM
> *To:* [email protected]
> *Subject:* Re: [EVGRAY] Szorenyi Rotary Engine Design
>
> Bart,
>
> Below are some possible solutions, if I knew more of what you are
> building I could be more specific.� My current project is undertaking
> the plasma magnetic field creation but will be utilizing RF pulses of
> a couple hundred watts from a� switch mode supply.� After preliminary
> research and configuring output to drive hydrogen thyratrons I may
> build the design into a half bridge for more control.
>
> How are you varying the stoichiometry of the HHO mix?
>
> For the power levels you are considering electric vehicle controllers
> look like the answer and are a bit pricey again unless you want to
> break out the soldering iron.� By the time you build 3 bridges to fire
> off a lower power controller it's that much more time involved.
>
> Here are two of the EV controller sources:
> http://www.fsip.biz/Documents/EVT1000%20Spec%20Sheet.pdf
> https://www.evwest.com/catalog/index.php?cPath=1
>
> These guys have some lower power controllers you could add IGBT boards to:
> https://www.goldenmotor.com/frame-bldcmotor.htm
>
> https://guide.alibaba.com/guidesearch.html?fsb=y&IndexArea=guide_en&CatId=&SearchText=BLDC+controller
>
> If I was to start from scratch with a chip rather than a
> microprocessor it would likely be one of these due to high frequency
> avail
> tps40090� controller
> https://www.researchgate.net/publication/3280891_Automotive_DC-DC_bidirectional_converter_made_with_many_interleaved_buck_stages
>
> http://www.electronics-lab.com/project/mc33035-brushless-motor-driver-breakout-board/
>
> http://www.ti.com/tool/TIDA-00909
>
>
>
> On 1/21/2019 12:30 AM, bart woodard [email protected]
> <mailto:[email protected]> [EVGRAY] wrote:
>> Mick,
>> ���������� It was quite the experience! lol
>> � When they could figure out who would be the officer in charge
>> (because it was three towns responding) said when they heard and felt
>> it they thought it was definitely a meth lab! hahahahaha
>> Had to think while shaking off the incident as to what� I would tell
>> them. You have to understand I ran it hundreds of times so it became
>> a very entrusted
>> component that I came to rely on, a stable standard . When it went
>> off it was only 2ft from me. I told them I was trying to develop
>> helium 5. lol
>> They of course did not believe me, but they settled as most of would
>> not really know anything. Over the next couple of days they came back
>> in groups of two and four several times asking again. I told them I
>> was busy. Then they asked if I would do a small seminar so they could
>> be prepared. I said sure , but was always busy.
>> They eventually settled down over all. In the next few weeks to
>> months some weird things happened with an f16 . They were doing
>> maneuvering exercises locally.
>> � Then on one afternoon my son and I were out front doing some yard
>> maintenance and I heard this unusual thrust sound.
>> Yep this guy came down and practically buzzed the tree line pulling
>> off green leaves from the trees like a cloud of green behind him, he
>> came in so low I could almost read his name on his helmet.
>> My boy ran behind the tree crying and asking me whats happening. I
>> told him they are just keeping security. He then did it again!! ,
>> looped, this time not so low.
>> I think really just to cover his butt back at base. There is a
>> ceiling restriction . I was going to go investigate but thought again
>> on it.
>> Then the drones started lol. Whoommmmmm� ha� ha ha. The neighbors
>> started to complain . I think really my house became a usual path for
>> the drones as
>> Canada had just okayed the allowance for 150 mile surveillance in
>> from the border. I really did set off the seismic graph so they told
>> me. hahahaha
>> So we got in the habit of holding up our Tim Horton coffee cup!
>> hahaha� Fun times!!!
>>
>> Ok on the implosion!�� Yes tried to find different ones available but
>> with no luck.
>> Rafael Morgado was to send a small version of his myt . Waited for
>> several years but it never materialized.
>> Mazda head office was to send in some motors and parts , but it was
>> when they were shutting down, so they got worried about themselves
>> instead of thinking forward.
>> So I decided to go with a bench build of an old single rotor
>> snowmobile motor, oddly I can not recall the brand just now.
>> But I set it up with some mods of an alternator 300amp @ 5 to 1�
>> ratio from the crank.I want to see what stoichiometry I am running with.
>> CFM is high but thinking I can loop most.
>> Hoping the work force per base does enough work required for the
>> timely values.**
>> Probably not good but I am hoping to change it up on the fly as needed.
>> I purchased an old 05 rx8 yanked the motor and am now waiting on the
>> 3 thou over sized ceramic racing kit for it.
>> Mick I do need something here maybe you can help source it if you
>> would. I need a controller , now days I am told you can get high amp.
>> So if its Christmas I would like to dial 0- 1200 amp 12 to 72 vdc
>> preferably one with a variant like ability ,one where I can tap up
>> and down on the lab top.
>> In my day I probably could solder and glue some thing up but now a
>> day no way.
>> Money is tight as I feeding to many generosities . Really need to get
>> back on the making money thing again.
>> ------------------------------------------------------------------------
>> *From:* [email protected] <mailto:[email protected]>
>> <[email protected]> <mailto:[email protected]> on behalf of
>> Mick [email protected] <mailto:[email protected]> [EVGRAY]
>> <[email protected]> <mailto:[email protected]>
>> *Sent:* January 20, 2019 7:28 PM
>> *To:* [email protected] <mailto:[email protected]>
>> *Subject:* Re: [EVGRAY] Szorenyi Rotary Engine Design
>>
>> Bart,
>>
>> I love Wankels, learned to rebuild them when I was 16 out of
>> necessity after my rx3 car seized.� That is an interesting rotary
>> engine with the pivot rotors however there is a way to get
>> compression without the eccentric shaft by adding an external
>> compressor like in a turbine, this could be dial a compression ratio
>> based on fuel type.� The Wankel is a no brainer for a diesel, not
>> sure why this has not yet emerged as it would run cool enough to poss
>> not have the fuel quenching issue.� The main issue with the Mazda's
>> is the area of the combustion chamber with the cooling galleys
>> running across it.� This causes a large thermal differential,
>> quenching the raw fuel that gets ejected out the tailpipe.� Seems the
>> rotary could be easily adapted to an implosion engine!
>>
>> What did you find experimenting with HHO and the possibility of
>> building an implosion engine?
>>
>> Some serious lab issues...� DAMN... sorry to hear this.� Glad you did
>> not get hurt or warehoused for blowing up Canada.
>>
>>
>> On 1/20/2019 3:46 PM, bart woodard [email protected]
>> <mailto:[email protected]> [EVGRAY] wrote:
>>> https://www.popularmechanics.com/cars/car-technology/amp25938374/szorenyi-rotary-engine/
>>>
>>> <https://www.popularmechanics.com/cars/car-technology/amp25938374/szorenyi-rotary-engine/>
>>>
>>> Szorenyi Rotary Engine Design | New Rotary Engine Design
>>> <https://www.popularmechanics.com/cars/car-technology/amp25938374/szorenyi-rotary-engine/>
>>> www.popularmechanics.com <http://www.popularmechanics.com>
>>>
>>>
>