Re: [EVGRAY] Dual rotor motorgen three coils row

Body

You might find it on the net it's used for circuit boards and some come
with out the copper .also you just might find it for general use in larger
sizes maybe I haven't yet .if you do let us know . some comes out of China .
On Aug 23, 2018 5:20 PM, "machinationus [email protected] [EVGRAY]" <
[email protected]> wrote:

>
>
> Fiberglass would be the easy way, and available thanks!
> Unless you want a conductor..
> On Thursday, August 23, 2018, 12:01:55 p.m. MDT, James Glinski
> [email protected] [EVGRAY] <[email protected]> wrote:
>
>
>
>
> Why not just use ceramics ? Or glass or fiberglass plate ?
> On Aug 22, 2018 3:08 PM, "machinationus [email protected] [EVGRAY]"
> <[email protected]> wrote:
>
>
>
> Thanks Warren, did you ever try zinc? I did try 303,304,316 and got mixed
> results.
> It may depend on manufacturing process..
> But it would work much better than aluminum if you could afford it!
> On Wednesday, August 22, 2018, 6:16:04 a.m. MDT, Warren Keillor
> [email protected] [EVGRAY] <[email protected]> wrote:
>
>
>
>
> Machinationus
> You are sure right about keeping diamonds cool. The ones I have been using
> are just brazed to the steel tube hole saws. As soon as the bronze melts,
> the diamond is shed, leaving no cutting action.
> 316L stainless is pretty non magnetic. You can do a very simple, and
> dramatically interesting test , yourself, if you have a sphereical neo
> magnet, and a selection of same size tubes, made out off different metals,
> and alloys.
> Just hold the tube vertically and drop the magnet down the tube.
> With aluminium, the eddy currents, will nearly stop the ball in the tube,
> which appears to float inside the tube when you look down counting the
> seconds it takes to fall a meter.
> With stainless 316 L , it drops as if you were using a ball bearing,
> inducing zero eddy currents.(and Lenz braking)
> Cheers Warren
>
> Sent from Yahoo Mail on Android
> <https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers&af_wl=ym&af_sub1=Internal&af_sub2=Global_YGrowth&af_sub3=EmailSignature>
>
> On Tue, 21 Aug 2018 at 11:31 PM, machinationus [email protected]
> [EVGRAY]
> <[email protected]> wrote:
>
>
> If you are using Diamonds then use lots of coolant (water) Diamond's are
> not "forever"
> They need to be flooded with coolant and run low lower speeds. Then it
> works good.
>
> CBN works the best for cutting steel or HighSpeedSteel..
> Stainless also doe's have a lot of Iron..
> On Saturday, August 18, 2018, 4:45:46 a.m. MDT, Warren Keillor
> [email protected] [EVGRAY] <[email protected]> wrote:
>
>
>
>
> Doug
> Ow, what a difficult task, even so.
> I think a trip to the local friendly water jet guy is in order. Stainless
> steel cuts beautifully within a few thou.
> I like to be able to do everthing at home, but stainless complex shapes
> are hard on the machinery that I have. Stainless works well with magnets,
> being invisible to them, and plenty rigid.
> Your off the shelf fiberglas discs are sure rigid and non magnetic, but
> man, what a skill you have with a chisel..
> Perhaps cast custom fiberglas discs complete with holes?....
> Cheers Warren
>
> Sent from Yahoo Mail on Android
> <https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers&af_wl=ym&af_sub1=Internal&af_sub2=Global_YGrowth&af_sub3=EmailSignature>
>
> On Sat, 18 Aug 2018 at 12:32 AM, [email protected] [EVGRAY]
> <[email protected]> wrote:
>
>
> Hi Warren
> I tried them and the carbide metal cutting discs would eat them up. I
> would of needed 16 of them to eventually drill 16 holes...hammer and chisel
> then epoxy worked well but doubling number of magnets and pinching them
> into rotor best way to go. Very strong and simple and super flat
> Kone
>
> 
>