Re: [EVGRAY] Here Talentman, play with this!

Body

Norman I may have found your first working on device !
On Mar 11, 2018 11:36 PM, "James Glinski" <[email protected]> wrote:

> I thought I would put this out there for you guys in case they do me
> unawares .no need to waste a idea..here's a possible OU device I thought up
> and it has some limits ..but you build a hho generator Meyer capacitance
> type shoot for best efficiency..then make a generator with a pulley
> setup...make a small platform .tie it to a weather  balloon .bubble the hho
> Thu a acetone or gasoline bath to stabilize it fill balloon .till it will
> lift several hundred pounds with platform .on plate form put a small hho
> motor generator and inverter for AC current ..as the balloon rides to 1000
> to 60000 ft it's cable is turning a earth bound generator so power going up
> .using two cables going up .when at the top drop the heavy weight pulling
> again the earth bound generator cable ..one comes down one holds platform
> .when the weight is  down the  hho generator fires up deleting the hho .and
> sending down the current Thu the cables ..as the hho diminished the
> platform will start to drop the earth gen slowly brings her back just
> keeping the lines tight ....the point is ..efficient hho .isn't lost in the
> process you get its power you get power from its bouncy up and it's weight
> comming down are a bonus rounds of energy .I don't think anyone has thought
> of using hho's lift to generate power and the dropping of a weight .plus
> .plus plus .and the rise would be unlimited ..well almost.. Think you could
> make power from the rise and fall of a ton at a mile up .? There's the free
> energy . frankly 500 ft would be the league limit here in the USA .  air
> plane's .and all .what do you think .needs a little tweaking ? My 30 pound
> hammer should do it .
> On Mar 11, 2018 7:58 PM, "Warren Keillor [email protected]
> [EVGRAY]" <[email protected]> wrote:
>
>>
>>
>> Hector
>> I just got it mostly assembled
>> The flywheel is firmly mounted and is good. It turns very freely.
>> The 1/2 hp bench grinder motor has a hard time. It just doesn't have the
>> torque needed to get off the starting capacitor to be able to get up to its
>> full speed.
>> It got too dark and cold to keep at it tonight, but I am thinking that I
>> could put a bored out hockey puck in a 7.5 inch side grinder and perhaps
>> press against the rim of the flywheel while at the same time use the
>> grinder motor which is connectedby vee belt to the flywheel.
>> Another approach is a 3 hp DC motor to drive it. I could use a heavy
>> variac and an equally heavy diode, and steadily raise the voltage and get
>> the flywheel up to speed, perhaps?
>> The other end of my challenge is the generator head.
>> It turns fine but does not put out the voltage. It was working fine when
>> taken out of service twenty -five years ago.
>> It is a 2.6 kw Troy -Bilt 3600rpm 120, 240 volt , 60 hz unit.
>> How to jolt it back to life?
>> I had this happen to me with a portable genset once after a lightning
>> storm.
>> It was dead as a nit for producing power though the motor was just
>> running fine.
>> Cheers Warren
>>
>> Sent from Yahoo Mail on Android
>> <https://overview.mail.yahoo.com/mobile/?.src=Android>
>>
>> On Sun, Mar 11, 2018 at 6:09 PM, [email protected] [EVGRAY]
>> <[email protected]> wrote:
>>
>>
>> maybe the idea is to make a synchronous motor out of it wired to 240 and
>> run on 120VAC synchronized to line then increase the excitation until it
>> takes power factor to a leading value ...or best low watts .. and use it as
>> a MOTOR generator ...(autonomous)
>>
>> (H)
>>
>>
>> ---In [email protected], <schoonersolsticemoon@...> wrote :
>>
>> Hector
>> I'm not sure what conversation this belongs in
>> I am, at present, hoping to drive my 100lb flywheel with a 3600 rpm bench
>> grinder, 120 volt 60hz motor 1:1 with a vee belt, that I can adjust the
>> tension.
>> The generator is a 2.6 kw 120/240 volt 3600 rpm unit intended to be
>> connected to a lawn mower for stand by power.
>> I had it connected to a hydraulic motor driven by an 85 hp diesel in my
>> boat.
>> Beyond a stupid microwave oven idea, I had no need for engine driven AC.
>> I hope to drive the generator at a slightly higher rpm than the 3600 to
>> adjust for losses.
>> This is my first set up for the experiment.  Buggering around with
>> belts,  and pulleys, should likely kill the day getting everything mounted,
>> but I will keep you posted.
>> Any suggestions from one and all are welcome.
>> Cheers Warren
>>
>> Sent from Yahoo Mail on Android
>> <https://overview.mail.yahoo.com/mobile/?.src=Android>
>>
>> On Sun, Mar 11, 2018 at 10:08 AM, arkresearch@... [EVGRAY]
>> <[email protected]> wrote:
>>
>>
>> [image: alt]
>>
>> Remember  will it be several poles or one freaking pole the method is the
>> same ,,, in making any brushed generator  into an original EV gray motor be
>> in in attraction or repulsion . RV is extra to the mix ,,, ( its the
>> seasoning )
>>
>> (H)
>>
>> 
>>
>