Body
I thought I would put this out there for you guys in case they do me
unawares .no need to waste a idea..here's a possible OU device I thought up
and it has some limits ..but you build a hho generator Meyer capacitance
type shoot for best efficiency..then make a generator with a pulley
setup...make a small platform .tie it to a weather balloon .bubble the hho
Thu a acetone or gasoline bath to stabilize it fill balloon .till it will
lift several hundred pounds with platform .on plate form put a small hho
motor generator and inverter for AC current ..as the balloon rides to 1000
to 60000 ft it's cable is turning a earth bound generator so power going up
.using two cables going up .when at the top drop the heavy weight pulling
again the earth bound generator cable ..one comes down one holds platform
.when the weight is down the hho generator fires up deleting the hho .and
sending down the current Thu the cables ..as the hho diminished the
platform will start to drop the earth gen slowly brings her back just
keeping the lines tight ....the point is ..efficient hho .isn't lost in the
process you get its power you get power from its bouncy up and it's weight
comming down are a bonus rounds of energy .I don't think anyone has thought
of using hho's lift to generate power and the dropping of a weight .plus
.plus plus .and the rise would be unlimited ..well almost.. Think you could
make power from the rise and fall of a ton at a mile up .? There's the free
energy . frankly 500 ft would be the league limit here in the USA . air
plane's .and all .what do you think .needs a little tweaking ? My 30 pound
hammer should do it .
On Mar 11, 2018 7:58 PM, "Warren Keillor [email protected]
[EVGRAY]" <[email protected]> wrote:
>
>
> Hector
> I just got it mostly assembled
> The flywheel is firmly mounted and is good. It turns very freely.
> The 1/2 hp bench grinder motor has a hard time. It just doesn't have the
> torque needed to get off the starting capacitor to be able to get up to its
> full speed.
> It got too dark and cold to keep at it tonight, but I am thinking that I
> could put a bored out hockey puck in a 7.5 inch side grinder and perhaps
> press against the rim of the flywheel while at the same time use the
> grinder motor which is connectedby vee belt to the flywheel.
> Another approach is a 3 hp DC motor to drive it. I could use a heavy
> variac and an equally heavy diode, and steadily raise the voltage and get
> the flywheel up to speed, perhaps?
> The other end of my challenge is the generator head.
> It turns fine but does not put out the voltage. It was working fine when
> taken out of service twenty -five years ago.
> It is a 2.6 kw Troy -Bilt 3600rpm 120, 240 volt , 60 hz unit.
> How to jolt it back to life?
> I had this happen to me with a portable genset once after a lightning
> storm.
> It was dead as a nit for producing power though the motor was just running
> fine.
> Cheers Warren
>
> Sent from Yahoo Mail on Android
> <https://overview.mail.yahoo.com/mobile/?.src=Android>
>
> On Sun, Mar 11, 2018 at 6:09 PM, [email protected] [EVGRAY]
> <[email protected]> wrote:
>
>
> maybe the idea is to make a synchronous motor out of it wired to 240 and
> run on 120VAC synchronized to line then increase the excitation until it
> takes power factor to a leading value ...or best low watts .. and use it as
> a MOTOR generator ...(autonomous)
>
> (H)
>
>
> ---In [email protected], <schoonersolsticemoon@...> wrote :
>
> Hector
> I'm not sure what conversation this belongs in
> I am, at present, hoping to drive my 100lb flywheel with a 3600 rpm bench
> grinder, 120 volt 60hz motor 1:1 with a vee belt, that I can adjust the
> tension.
> The generator is a 2.6 kw 120/240 volt 3600 rpm unit intended to be
> connected to a lawn mower for stand by power.
> I had it connected to a hydraulic motor driven by an 85 hp diesel in my
> boat.
> Beyond a stupid microwave oven idea, I had no need for engine driven AC.
> I hope to drive the generator at a slightly higher rpm than the 3600 to
> adjust for losses.
> This is my first set up for the experiment. Buggering around with belts,
> and pulleys, should likely kill the day getting everything mounted, but I
> will keep you posted.
> Any suggestions from one and all are welcome.
> Cheers Warren
>
> Sent from Yahoo Mail on Android
> <https://overview.mail.yahoo.com/mobile/?.src=Android>
>
> On Sun, Mar 11, 2018 at 10:08 AM, arkresearch@... [EVGRAY]
> <[email protected]> wrote:
>
>
> [image: alt]
>
> Remember will it be several poles or one freaking pole the method is the
> same ,,, in making any brushed generator into an original EV gray motor be
> in in attraction or repulsion . RV is extra to the mix ,,, ( its the
> seasoning )
>
> (H)
>
>
>