More over unity

Kathy and I went to Joe’s for the weekend. It’s a 6 hour drive each way. Kathy has Thyroid issues and the Drs (if you can call them that) just want to cut out that which they don’t understand. They do it every day and then you are ‘theirs’ forever to milk. Kathy had been pestering me to take her as its been 6 months since our last visit. There was a time I went every month for a few days. Dragging the Mrs along stops this spontaneous travel. 
 First thing after brekkie on Sat morning, Kathy and Joe sat on a bench with a sony handycam recording Joes every move for an instructional video of Body Electronics. He asked if I was going to put it on the net and I replied not til we are dead and then it will be worth a fortune. Don’t tell Joe, the world thinks he’s already dead as most don’t see any value in JoeCell technology. After Joe was finished, it was my turn, but fortunately the battery went flat half way through. I am spared the notoriety. Kathy got the ‘full’ treatment for Point Energising.  I have seen it done many times before in the last 16 years and have some limited video of the procedure. Many ‘miracles’ have walked out the door afterwards. Last Saturday was no different. After a cup of coffee to charge the battery on the sony, we went down to the shed to see the latest in OverUnity. For 3 hours it was just electricity. He had about 20 Fisher and Paykel motors laying on the benches. He had one from the UK that had only 3 wires attacked to it. All the rest have 3 in and 3 out. (or so) But we didn’t get to see that one run. There was a unique design of ‘pipes’ with grooves in the pipes for ring magnets to slide along but he didn’t want to show that one yet as its not assembled. (think of making a car piston magnetic and the cylinder bore with groves in the water jacket as a generator Add-On for an ICE motor that runs Cold  Why add a Generator to a petrol motor??) Joe always pulls them apart after they work to stop sticky fingers and prying eyes. He rotated an AC motor with a cordless drill to light up bulbs and we all took turns grabbing the bare wires, just like Morin does in demonstrating cold electricity. (everyone here it seems, only knows of hot electricity) But he did have functioning over unity setup on the bench. It consisted of a 12V motor bike battery that was so flat it barely lit a test bulb. It was connected to an inverter which was connected to FisherPaykel (FP) motor where the output went to an AC Generator, 3 x 150 watt Work lights, and a 240 AC motor with a polishing wheel attached. The ‘Load’ was considerable. This 12v bike battery powered up the Fisher Paykel washing machine motor that drove 3 Work lights, a bench grinder of sorts and an AC generator and the 3 lights more than warmed the hands in the cold winter air of the shed. It ran for about 20 minutes and he then went on to show me other apparatus’s. I asked to take pictures but was given that look again. The power coming out of the apparatus one could easily hold the electrodes and not feel a thing.  One of the points I was being instructed in was that to generate electricity, its all about the EDDY Currents. They can lock up any device thats not given some Load. Can twist off shafts if the Boat Anchor Chinese Generator has enough inertia. The FP motor only spun at 60 rpm to generate about 2000 watts if one adds up the ‘Load”. You do not need rpm. You do not need a control firing/timing mechanism. 
 Joe wasn’t happy with this as its not UNIQUE enough for him. So he next showed Kathy as I have seen it all before, how to generate power without the FP motor rotating but by just oscillating about 5 degrees back and forth. So it runs forever never wearing out bearings etc all the while still warming the hands with the 3 x 150 watt work lights on a cold winters day. Later that evening Joe went through some youtube videos he had been watching about Morin and his ‘attempts’. Funny how youtube isn’t watching the internet (something he never did) when its on the TV via satellite in his lounge room. We watched several and everything Morin did and discovered, Joe has done and showed me over the last 10 years. Everything everyone is looking for and more, sits on a bench in Australia. If I were to build it or publish it, I negate any further IP transfer. Having seen several Solid State over unity generators and a couple rotating ones as well, cracking this Cold side of Electrical energy production is going to take someone like Morin to be shown a few new clues as to how its done. The rest of you will tinker and share …… forever.... a very limited design.
  
 A spinning Top pivoted on the edge of a bench defies gravity because of Eddy Currents. An old school spinning aluminum wheel Electrical Meter operates not by friction but by Eddy currents. A spinning car wheel levitating above the ground gives Friction by Eddy Currents. A spinning planet interacting with other spinning planets gives rise to Eddy Current Winds and Eddy Ocean Currents. Sunspots are Eddy Currents that have the Planets as an Aspect of their Origin. Spinning magnets generate electricity by Eddy Currents. These currents have a polarity and most only ever use the hot side as it’s the side they ‘see’. Having built a back emf spark collector that ran at 1000 rpm, this isn’t what one is looking for. 
  
 If anyone has thyroid issues and wants them fixed rather than cut out or some pointers on their Boat Anchors, I will be driving from LA to NY and back again during the Month of August in 2 weeks time.