Re: [EVGRAY] 8 motorgen coil sandwich

Body

I'm in hunting territory in the  country.. logging area three miles from a
paved rode  and electric and city water . just me and the anamals out here
and the people who basically live with me and there electronic weapons .
hope you get some heat going soon can't  imagine working in that level of
cold . are you getting the walls up ? At lest some clear plastic ?. They
say there's a job in Alaska up by one of the northern oil fields that has a
cabin with a diesel generator and if it fails you just die no recourse .
diying ant much of a living . good luck with your work Warren .time to take
a swat  at the cat .

On Tuesday, November 20, 2018, James Glinski <[email protected]> wrote:

> Well it's just a conundrum to me on one vid he and Rick were very excited
> about it like trying to correct an  oversite on there part .they didn't say
> it wouldn't work they just said it should be there and you get 30% more out
> of it by being connected to the earth .I was going Thu the stuff on the web
> a some have it some don't . so there we are stuck in low die again .I'm
> going to see if I can find Rick .
>
> On Tuesday, November 20, 2018, Warren Keillor
> [email protected] [EVGRAY] <[email protected]> wrote:
>
>>
>>
>> James
>> There was no earth ground on my Bedini Wheel, just big deep cycle 6 volt
>> golf cart batteries, a load and a lawn mower battery driving it.
>> Sometimes more than ten 225 amp batteries in parallel (and series, as
>> they were 12 volt coupled in pairs)
>> Today, I am trying to move some of that stuff from a leaky shed to a nice
>> dry barn, along with a 4'X8' cnc panasonic XY table, which I might now have
>> room to finally set up in a permanent location,  with a laser head. First
>> though, is to get the delicate screw drives, cast iron dove tails and gear
>> heads out of the drippy roof area of the shed, as it is only covered with
>> plastic sheeting, to protect it. The squaller of moving! The bonus of
>> space! Plenty of work here.
>> The Bedini wheel is mounted on a four foot 3/8" plexiglas disk for
>> mounting all the coils around the wheel, which is a tubular stainless steel
>> big yacht wheel, turning in precision skate board bearings, with a power
>> take off shaft for future experiments with mechanical indexing. It has been
>> stored in a rather dry corner, and seems like it hasn't been hurt too much
>> by the move. It will be good to get all the energy stuff together in one
>> place, more, or less, after almost a year of chaos. Many of the out
>> buildings don't have electricity yet, as I have been trying to get roofs,
>> walls, and foundations on the big building, and a heated floor in my stone
>> workshop building, which should soon be working, this weekend.
>> Just using a quartz lamp, it has been above freezing in there on the
>> retained heat and urethane foam insulated roof! It was -16C one night last
>> week outside.
>> The CNC setup won't be heated, but at least it will be dry.
>> Are you in the city, or in the country where you are?
>> Cheers Warren
>>
>>
>> Sent from Yahoo Mail on Android
>> <https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers&af_wl=ym&af_sub1=Internal&af_sub2=Global_YGrowth&af_sub3=EmailSignature>
>>
>> On Tue, 20 Nov 2018 at 7:39 AM, James Glinski [email protected]
>> [EVGRAY]
>> <[email protected]> wrote:
>>
>>
>> Warren where did you put your earth ground on your Bedini wheel ..I've
>> been looking at his diagrams and theres a lack of consistency in showing
>> the earth grounds mixing chassis ground symbles and earth ground symbols
>> and he said it was important giving 30% more charging power .most of his
>> work doesn't show it . just thought you might know .if ask him but he went
>> and died .
>> On Monday, November 19, 2018, Warren Keillor
>> [email protected] [EVGRAY] <[email protected]> wrote:
>>
>>
>>
>> Mick
>> Urethane works well with carbon fibers, can be ,like Doug is doing,
>> encased in epoxy, or like I used to do years ago, mix aluminium powder in
>> with it.
>> The Very Easy home built was styrofoam encased in epoxy resin and glass,
>> but would be even lighter using carbon fibers. These are generally nice
>> materials to work with, as the epoxy is not very stinky, like polyester,
>> and won't eat the styrofoam. Did you know that the padded dash in your car
>> might be self skinning urethane, appearing to be a soft vinyl, but actually
>> soft urethane rubber, with a spongy foam interior. Tooling is quite cheap
>> for urethane production work, and I could even turn out widgits in my
>> studio, like soft, light weight link chain, suitable for zombies to have
>> fights with bashing each other. Or swords, crossbows and the ilk, so people
>> could fall off their horses on them( I could have used something soft to
>> land on, myself, falling off old Snoopy at 30 miles an hour, in New
>> Zealand!)
>> Anyway, we shouldn't have problems with materials, it is the
>> configuration, and like that rumored
>> Sail boat electrical generator system, or Zilano's farm supply, we have
>> some serious reverse engineering, that we are called upon to deliver, not
>> discounting a host of other fairly good devices.
>> Now that Rosemary Ainslie is sticking up for herself against the nasty
>> trolls, a lot of replications have come forward.
>> Cheers Warren
>> Sent from Yahoo Mail on Android
>> <https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers&af_wl=ym&af_sub1=Internal&af_sub2=Global_YGrowth&af_sub3=EmailSignature>
>>
>> On Mon, 19 Nov 2018 at 2:50 PM, Mick [email protected] [EVGRAY]
>> <[email protected]> wrote:
>>
>>
>> Warren,
>>
>> For another serious plate material one can lay up and bag carbon fiber,
>> my neighbor does it all the time for his airplane parts with a cheap Harbor
>> Frieght Robinaire vacuum pump.  Even the urethane's could be strengthened
>> easily with a carbon skin in this manner.  How about spinning graphite
>> rotor, Tesla did claim it was the best conductor or radiant energy.
>> On 11/19/2018 3:50 AM, Warren Keillor [email protected]
>> [EVGRAY] wrote:
>>
>>
>>
>> Doug
>> That is cool that you have a source of supply.
>> Here in Ontario, Sculpture Supply provides a very large spectrum of
>> interesting materials, among them the product lines of an American company
>> called Smooth On
>> The catalog, covers virtually everything one could need to make anything
>> out of plastic or rubber, in any configuration, plus the materials to make
>> molds.
>> It was here I was able to buy iron powder, for instance, or copper
>> powder, and a host of strange things hard to get otherwise.
>> I cast up my own motor mounts for the 1935 Morris, and also a clear
>> plastic headlight lens, identical to the one glass one I had, which is
>> staying perfectly clear several years later.
>> When you make up a perfect hero pattern, you can then make a silicone
>> rubber mold and make urethane copies, out of a whole range of urethanes
>> from clear rigid to skin soft, or like shoe soles , or tires.
>> Keep it in the back of your mind for the future.
>> Cheers Warren
>>
>> Sent from Yahoo Mail on Android
>> <https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers&af_wl=ym&af_sub1=Internal&af_sub2=Global_YGrowth&af_sub3=EmailSignature>
>>
>> On Mon, 19 Nov 2018 at 5:34 AM, [email protected] [EVGRAY]
>> <[email protected]> <[email protected]> wrote:
>>
>>
>> Hi Warren
>> EBay and Russian type eBay companies I can get,stuff but takes awhile to
>> be delivered ...got a lot of Soviet litz wire from nearby ukraine..the
>> urethane I get from hardware stores cut frim concrete float paddles that
>> they use to smooth wet concrete.
>> Kone
>>
>> 
>>
>