Re: [EVGRAY] Magnifing transmiter FCC permit

Body

Warren,

Will brass get hot on an inductive stove?


On 10/25/2018 8:49 AM, Warren Keillor [email protected]
[EVGRAY] wrote:
>  
>
> Dave
>
> The eddy currents in a brass core will get it hot, I would expect.
> Cheers Warren
>
> Sent from Yahoo Mail on Android
> <https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers&af_wl=ym&af_sub1=Internal&af_sub2=Global_YGrowth&af_sub3=EmailSignature>
>
>     On Thu, 25 Oct 2018 at 11:09 AM, Dave Muckerman [email protected]
>     [EVGRAY]
>     <[email protected]> wrote:
>      
>     Does anyone not know using brass instead of iron in a core will
>     make any coil less inductive than no core or air?
>     Wonder if anything good could result?
>
>     air coils don't saturate right?
>
>
>     On Thursday, October 25, 2018 8:03 AM, "Norman Wootan
>     [email protected] [EVGRAY]" <[email protected]> wrote:
>
>
>      
>     James!   During my many years of hands on Electrical Contracting
>     and Researching electrical phenomenon, my first real brush with
>     the Neutral Spike was while designing small electric motors in
>     1981. This was a tall stack shaded pole motor that was designed to
>     be reversible by switching the position (electrically) of the
>     capacitor in series with the start windings via double pole/
>     double throw reversing switch.   This new prototype motor was MFG
>     in Chine and test samples were shipped to me for QC testing. 
>     Destructive testing included the reversal of the motor while
>     running full speed forward via switching the reversal switch! When
>     switched the double throw switch literally exploded with a loud
>     WOOOMP! and a bright green flash. (vaporized copper). I had a
>     double EE Professor from UT Arlington come over and observe the
>     phenomenon. since the whole 1/6th HP motor was being run off 18ga.
>     zip cord with earth bond ground wire to motor frame, it was quit
>     bizarre to see a 30 amp rated switch just explode. His
>     calculations could not explain where the burst of energy came
>     from. After welding the contacts of several heavy duty reversing
>     contactors and examination of the original motor schematic with
>     the wiring as received from China ,I found that the little lady in
>     tennis shoes (assembly line Chinese lady) had placed the reversing
>     circuit and switch on the neutral side of the line input. In
>     effect (when in transit) the entire motor electric circuitry was
>     in an isolated state (floating neutral) condition which is a great
>     big NO, NO, This set up the perfect scenario for the neutral spike
>     from earth ground to occur.  I have written all this up several
>     times before for this EVGRAY site. Most people do not understand
>     how shaded pole motors work much less how you reverse their
>     rotation. You have to reverse the rotating magnet field by phase
>     angle 90 degree leading or 90 degree lagging (start windings)
>     relative to the main run windings. See:
>     https://en.m.wikipedia.org/wiki/Shaded-pole_motor
>     https://woodgears.ca/motors/reversing.html
>
>     On 10/24/2018 10:10 PM, James Glinski [email protected]
>     <mailto:[email protected]> [EVGRAY] wrote:
>>      
>>     Just my opinion but that looper might be a version of the pulse
>>     led out research .a Chinese guy mad a wheel and found that if you
>>     pulsed once you get three back .the heavy fly wheel would absorb
>>     the  kinetic energy from the pluse and run the DC generator .the
>>     board would control the pulse timing .a1000 watt pulse would
>>     return 3000 watts in kinetic energy .spread that energy around
>>     the pancake motor coils to reduce general over loading of a
>>     single .point .but the Chinese version doesn't use iron cores
>>     .this is a lot like bedini's first self runner but he adjusted it
>>     for one battery .and ran for 15 years .what if he adjusted it for
>>     ten ?
>
>     https://www.johnsonelectric.com/en/resources-for-engineers/ac-motors/principle-of-operation
>
>
>
>>     On Oct 24, 2018 3:35 PM, "Mick [email protected]
>>     <mailto:[email protected]> [EVGRAY]" <[email protected]
>>     <mailto:[email protected]>> wrote:
>>
>>          
>>         Norm,
>>         How many different setups did you use in your formal
>>         investigation of the neutral spike,  I know about the locked
>>         rotor motor but were there others?
>>         There seems to be some crossover with Don Smiths claims of
>>         aluminum and copper used as opposing capacitor plates and the
>>         work of the builder of the Swiss Testatika machine.
>>         What if any interesting observations have you made in re to
>>         the copper/aluminum function?
>>
>>         On 10/24/2018 12:13 PM, Norman Wootan [email protected]
>>         <mailto:[email protected]> [EVGRAY] wrote:
>>>          
>>>         Mick! I was the first on this site to bring up the
>>>         Evenescent wave &
>>>         critical angle for it was in my research on a zero loss
>>>         solar heat
>>>         collector.     This tied in directly to MBKIng work on the
>>>         plasmoid
>>>         experiments.
>>>
>>>         https://web.stanford.edu/~ ajlucas/Evanescent%20Waves.pdf
>>>         <https://web.stanford.edu/%7Eajlucas/Evanescent%20Waves.pdf>
>>>         https://en.wikipedia.org/wiki/ Evanescent_field
>>>         <https://en.wikipedia.org/wiki/Evanescent_field>
>>>
>>>         On 10/23/2018 7:37 PM, Mick [email protected]
>>>         <mailto:[email protected]> [EVGRAY] wrote:
>>>         >  Zenneck or Evenescent wave
>>>
>>
>
>
>
>