Body
(H), From my very first encounter with EMP back in 1981 while working as
Director of Research & Development for a ceiling fan manufacturer, was
doing final acceptance,destructive testing of new production samples
from China. The motor samples were a tall stack Emerson copy that had a
reverse feature. (1/6th HP). The reverse feature was accomplished by
moving the run capacitor from one end of the shading windings to the
other end via a double pole , double throw Carling toggle switch.
Hookup wire was 18 ga. zip cord 2 conductor. Motor drew 1.75A @120VAC =
210 watts. Testing included severe loading by running motor full speed
forward, then reversing (toggle switch) which caused motor to grind to a
stop , then spool back up to speed in reverse rotation. After several
reversal operations, the toggle switch exploded with a bright green
flash and the bang of a big fire cracker. Tear down of motor and
inspection found no damage to the 22 ga. motor windings nor to the 18
ga. internal switch circuit wiring. ???? The Carling 30 amp rated double
pole, double throw switch was totally destroyed with contacts
vaporized. After vaporizing several switches in subsequent test, I
called in an Electrical Engineer Professor from University of Texas to
observe the abnormal operation. We destroyed another switch then changed
the reverse switching to a large double throw motor reversing contactor
rated at 60 A. The contactor exploded with total destruction of
contacts with bang of huge firecracker and bright green flash. The
Professor could not explain the destructive force created from such
small wiring and only a 210 watt line draw from motor. The 20 amp panel
breaker did not trip in any of these episodes. Here is the explanation
as to what caused this whole scenario. After studying the schematic
of the motor wiring plans and comparing with the (as assembled) by
little ladies in tennis shoes (China), it was found that reversing
switch was wired on neutral side of line input instead of the hot side.
All generation of the EMP shot requires that you isolate a charged
capacitor and saturated motor windings to create the effect you are
looking for. The little Chinese Ladies created the isolation effect by
incorrect switch placement. by complying to motor specifications, the
problem was corrected, but I learned how to create the EMP easily.
Years later I did the exact same transit switching isolation of charge
in the 5 ton A/C compressor which was a magnum version of the little
ceiling fan shaded pole motor event. The single phase 230VAC, 5HP
motor uses L1 & L2 line with no neutral in the schematic. Motor frame
and chassis is bonded to earth ground. The start capacitor is 45mfd
and run is 5mfd. See schematic:
By using an overcurrent relay in the contactor control circuit you can
adjust the contactor trip current at peak locked rotor saturation
current which is 82mamps for this type of motor. when contactor drops
open the entire motor/capacitor wiring is isolated from a neutral
return, with only the motor iron and frame bonded to earth ground. the
cancellation of magnetic flux and capacitor charge developes a Neutral
spike out of the earth bonded side of the circuit. You did not destroy
the energy, you just changed its form into a Aetheric event. Yes,
Hector it is quite a sight to see this event. Have fun. Norm
On 4/2/2018 6:57 PM, [email protected] [EVGRAY] wrote:
>
> ASK NORMAN HE KNOWS WHAT A NEUTRAL SPIKE CAN DO .....!!!
>
>
> (h)
>
>
>
> ---In [email protected], <lutzliebers@...> wrote :
>
> Sounds like doomsday-physics!
>
> :-)
>
>
>
> Am 02.04.2018 um 21:18 schrieb arkresearch@...
> <mailto:arkresearch@...> [EVGRAY]:
>
>> If the coil is OU the coilbanger will keep flashing forever or
>> will simply go into self destruct mode by gunning itself to a
>> huge EMP event ...\\
>>
>> (H)
>>
>
>