Body
Thanks Mick., A photo of the transformer of the Modified 3-phase socket is coupled with the last message I attached. The heatsinks are from defective forklift control units that were passively cooled, which I got as a gift from our forklift mechanic. Greetings Sven
Von Samsung Mobile gesendet
-------- Ursprüngliche Nachricht --------
Von: "Mick [email protected] [EVGRAY]" <[email protected]>
Datum:22.03.2018 19:02 (GMT+01:00)
An: [email protected]
Betreff: Re: Aw: Re: Re: [EVGRAY] Re: Strobe Experiment
Beautiful Sven you have style!
Where do you get the giant heat sink?
Is the transformer to the right side outside the frame of the picture?
On 3/22/2018 9:51 AM, [email protected] [EVGRAY] wrote:
Hi Warren, in your case you want to pull out of the capacitor phase energy to do anything.
When Coilbanger I can not change the current direction, the coil has the endeavor to maintain the current direction, it acts like a battery. Through the transformer I can change the direction of current and lead it back into the capacitor - that's the idea.
I have finished my new diode plug system now or finished last week. With the new components, everything can be set even more precisely and cleanly. I have now attached flywheel diodes with 75W bulbs to the anodes of the SCRs. So you can visually see the strength of the impedance or how much energy is transferred or not at high impedance shine brighter as at low impedance, it may be a bit of gimmick.
I have perfected the system, the question now is how do I use these short strong impulses now. With 400 to 500V pulses directly to the battery switch, because I have no good feeling.
I would like to build a universal buck converter, I still have a few components to build the rough and a HF core synonymous. Just take a look.
regards
Sven
Gesendet: Donnerstag, 22. März 2018 um 16:25 Uhr
Von: "Warren Keillor [email protected] [EVGRAY]" <[email protected]>
An: "[email protected]" <[email protected]>, "[email protected]" <[email protected]>
Betreff: Re: Aw: Re: [EVGRAY] Re: Strobe Experiment
Sven
It might not be the same situation, but with my RV, I did drive yet another RV identical to the first one, without a transformer.
It didn't prove anything, perhaps, except that the transformer in series with the capacitor circuit was not in all cases essential, with RV.
One RV had grease, and seals, the other had been cleaned, but they were identical 3 hp WEG 480 volts 3 phase.
Cheers Warren
Sent from Yahoo Mail on Android
On Thu, Mar 22, 2018 at 11:04 AM, [email protected] [EVGRAY]
<[email protected]> wrote:
I also think that you have to use a transformer to send the energy back in the right direction, preferably with higher voltage.
regards
Sven
Gesendet: Mittwoch, 21. März 2018 um 19:51 Uhr
Von: "Dave Muckerman [email protected] [EVGRAY]" <[email protected]>
An: "[email protected]" <[email protected]>
Betreff: Re: [EVGRAY] Re: Strobe Experiment
For the (H) coil bangers here:
I think a small choke winding series to diode across flash tube is needed for PIV protection, stopping nasty 6KV+ trigger pulse.
Diode keep lamp from ionizing too.
OR fire lamp into auto-transformer, side-winding-diode recharges the lamp storage cap. and forget about diode across to lamp.
Easy to wind a pulse transformer and you rewind it until perfect.
A great new source for cheap HV non-polar hi freq. tough capacitors. Induction stove MKPH 5% type. 600v up to 1200, & up to 1 ufd
values. good up to 150khz and self healing too.
E-bay, write the seller for discount for 16 or so
ATTN: (H)
(Unless energy reverses on the banged coil back through the diode across lamp as (H) writes and it refills the cap or writes in foolproof hookup detail.)
On Wednesday, March 21, 2018 12:47 PM, "[email protected] [EVGRAY]" <[email protected]> wrote:
Kapednaze = genesis
"self cancelling opposed fields and a turn rate defined variometer magnetic field angle modulation"
(H)